A word to the numerous spammers using this article to spam my website: It’s completely wasted time to copy & paste nonsens messages like “I used to be able to find good advice from your blog posts.” etc. together with an URL to enhance search engine scoring for your website. I read ALL the comments submitted and put them to trash instantly when they have got nothing to do with the technical topic of this (and all other) articles. So my advice: Don’t do it! You’re just wasting time!
by Peter Rachow (DK7IH)
After having built my first shirt-pocket transceiver about a year ago I occasionally thought of how this or a more or less modified design could be made simpler to save components and therefore limit space as well as reducing the complexity of the whole rig. This was due to the fact that I thought that the ancestor (see link above!) of this project was somehow „overkill“ because I used plenty of stages redundantly that could have been used for receive and transmit operation.
Before we go into the details of this new project, let’s have a look on the new micro transceiver (here operating portable as EA8/DK7IH/QRP from the island of Fuerteventura):
Cabinet size is about 10 by 4 by 5.5 centimeters which equals to a volume of 220 cubic centimeters (cm³).
Making it more simple without detereorating the performance?
Under the aspect of simplifying the circuit I remembered that I had searched for simple designs of transceiver circuits some years ago intensely. After having revisited some of them on the Internet my attention was caught by the „Antek“-Transceiver that has been published by SP5AHT a while ago. This was an ideal basis for my purpose because I intended to build a „2 mixers+1 filter“ circuit in order to make at least 2 of the 4 mixers that are necessary for a fully functionally SSB transceiver redundant. The central part of SP5AHT’s design matched my requirements in an ideal way:
SP5AHT’s circuit uses one mixer (US2 in the schematic) to serve as the receive mixer during rx periods and for the balanced modulator when on transmit. Then the resulting signal is fed through the filter and subsequently processed by mixer 2 (US3). This mixer works as the product detector on receive mode and as transmit mixer when you are on the air. The two oscillators (VFO and LO) are fed to the respective mixer depending on the current operation. This is done by a simple relay connected to the PTT. So when changing from receive to transmit the two oscillators are swapped thus changing the complete function of the circuit.
To get rid of the relay and because I wanted to use the Si5351A clock oscillator chip, my idea was making two of the 3 oscillators present in the clock chip act as LO and VFO. By software, when switching from rx to tx, these oscillators’ frequencies are simply swapped. The microcontroller driving the Si5351A reads the PTT and when pressed to talk the frequencies present on CLK0 and CLK1 are put out reversely. Thus no hardware switching is required.
In addition the audio amps in the end of the receiver chain are powered off. Instead of this the rf power amp of the transmitter section is connected to +12V DC as well as the microphone amp. The antenna relay disconnects the receiver front end from the antenna line and connects the antenna to the LPF that is installed after the rf power transformer of the rf power amp final stage.
By this the whole transceiver is constructed much simpler and lots of circuitry has been removed from the rig.
The block diagram
Circuit explanation: During receive periods the signal is fed into the antenna jack whose line is switched by the antenna relay and fed to the first band pass filter for 14MHz when listening to the band. Afterwards it is amplified by a dual-gate MOSFET transistor that is connected to the AGC line that reduces gain when strong signals are detected. The next stage is mixer 1 where a VFO signal of about 24 MHz comes from CLK0 of the Si5351A module.
The result of this mixing process is the IF of about 9 or 10.7 MHz or whatever frequency you are about to use depending on the filter you have installed. This signal is amplified by another dual-gate MOSFET. On receive mode this stage is also under AGC control. When transmitting it is powered to full gain of about 18dB applying +12V via a 2:1 voltage divider consisting of 2 resistors with 82k each.
Next step is mixer 2 where the IF signal is mixed with a 9 resp. 10.7 MHz LO signal (receive mode serving a product detector) or with the VFO signal in mixer 2 serving as tx mixer.
On receive two audio stages (a preamp with LPF in advance and a power amp) amplify the audio signal to a level that can be fed into an 8 Ohm loudspeaker.
On transmit a BPF eliminates the unwanted mixing products and a three stage rf power amplifier lifts the signal to a power level of 3 watts peak power.
The Main RF Section
This central section of the rig consists of the two mixers mentioned before, a off-the-shelf made (in my case) 10.695 MHz filter stripped from an old CB radio, some amplifier stages and so on. The circuit is the following one:
Starting from left side top there is the first receiver amplifier stage using a dual-gate MOSFET. The use of a MOSFET transistor ensures that the noise figure and sensitivity of the whole receive improve very much. The stage is comnnected to the AGC chain. The dc voltage applied by the AGC section varies in the range from 0 to 6 V DC. In addition it can be set by hand by turning a front panel mounted potentiometer that alters the DC voltage in the range from 0 volts to max. volts from the ADC section.
The input is a single tuned circuit using 4 (antenna side) by 16 turns (MOSFET gate side) on a TOKO 5,5 mm coil former. Parallel capacity is 47 pF. In drain line of the transistor the same filter is used coupling the signal to the first mixer (NE612). Note that the second filter is reversed (secondary in drain line) to avoid self-oscillation of the preamp stage.
This mixer’s signal is fed with 2 different input signals (antenna or microphone) and with 2 different oscillator frequencies: about 24 MHz on receive mode or 10.695 +/- 1.5 kHz depending on sideband used when on transmit. The resulting interfrequency signal is fed into an SSB filter which is terminated by 2 resistors of 1k each side to ensure proper impedance matching.
Next stage is the interfrequency amplifier which is the same circuit like the receiver’s preamplifier. This one is also connected to the AGC’s DC line. On transmit mode with no AF signal on the AGC present this stage runs on full gain.
The chain is completed by the second mixer serving as product detector on receive and as tx mixer when going “on the air”.
The audio and AGC section
This section also is no “rocket science”. A simple preamplifier using a bipolar transistor (BC846) in common emitter mode, a low pass filter (R=1k and C=0.22uF) and an LM 386 amplify the resulting af sig to an adequate volume to listen to the sound even in an environment that is not 100% noise free.
The RF power module
This is a circuit I have built several times and it’s capable of delivering up to 5 watts of rf power. In this transmitter I’m not driving it beyond 3 watts which is suffice to establish connections on the 20 meter band worldwide a well performing antenna provided.
Emitter degeneration and negative feedback are present in preamp and driver stage to ensure maximum linearity. Both stages are operated in class A mode. The final stage works as a push-pull stage using class AB. Push-pull mode eliminates even order harmonics by circuit feature. A heatsink is mandatory for the final stage (the mounting frame in my case) and at least recommended for the driver. The values for the broadband transformers are stated in the schematic above.
The VFO module
This one is equipped with the clock oscillator chip Si5351A by Silicon Labs. I use it mounted to the well known Adafruit breakout board that can handle 5 volts even if the chip is designed for 3.3V. So, this board is compatible to standard microcontrollers like the ATmega168 that is applied in my transceiver. The display is the 1306 chipset based OLED that is also designed for 5 volts supply voltage. Both, the Si5351 and the OLED are designed for I²C-interface which is called “Two Wire Interface” (TWI) in Atmel’s language. The major advantage this interface has got is that only 2 control lines are required, one of them clock (SCL) and the other data line (SDA) to transfer data to the respective units. Basically you need two pull up resistors to tie these lines to +5VDD but I use the internal pull-up resistors in the Atmega168’s ports that do the job well.
Problem to be mentioned: When testing the early version of the receiver I found the OLED to be very noisy. After a brief research I realized that the signals that were audible in the receiver traveled on the VDD line. Thus I inserted an 82R series resistor and a set of blocking capacitors in the place which made the noise fully disappear.
The main board of the transceiver is made of a 5 by 7 cm breadboard with double-sided soldering pads each connected by a small tubing electrically connecting the both sides of the pad . This is a big advantage when you solder SMD components because you can setup the circuit on both sides of the board and save a lot of space. NExt is that it is nearly impossible to dissolder the pads even if you are resoldering the spots many times. The reason: The soldering pads are rivets anchored on both sides of the carrier of the board.
The components that aren’t available in SMT are standard through-hole but there are only a few like the SSB filter or some old 40673s I used instead of e. g. BF991. Coils for low power are wound on TOKO 5.5 mm coil formers. Power rf transformers are connected to soldering nails in the board. The inside view plus a centimeter scale:
On the left you can see the front panel with the controls, behind the panel the OLED and then the main rf board. The Si5351 is mounted vertically on top left from the AGC board. Underneath there is the receiver’s front end (hidden by the red power supply cable). On the right I sited the power transmitter, at the bottom there is the relay for tx/rx switching. All is built into a 9 * 5.5 * 4 cm Aluminum frame.
Being “on air” with the rig
Operating is really fun with this micro transceiver. Since the finishing of the transceiver 4 weeks ago I was on air daily. Here are some regions of the world I could establish successful contacts with. Antenna is a Delta Loop fed in on upper corner about 12 meters above ground.
Plans for the future
Several options may be my next project: First I got plans are to expand this rig to a multibander (due to Si5351’s capabilites of generating max. 160MHz signals), build a PA of about 30 watts max. power (with 2 transistors 2SC1969 in push-pull mode) or to rebuild the transceiver for 17 meter band and hoping that conditions will be better the next couple of years. Let’s see what the real deal will be! 😉
73 de Peter (DK7IH)